Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGAMID® A70GK30 - PA66-GB30 - Avient Corporation

Material Data Center offers the following functions for BERGAMID® A70GK30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergamid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 물질의 비성질 - 테스트 견본 생산
Any use of this information falls under the rules of our disclaimer.
제품 설명서
BERGAMID A70GK30, PA66 reinforced
30% glass bead, general-purpose injection molding grade
good surface finish
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 2800 / 5000 MPa ISO 527
파단시 강도 70 / 90 MPa ISO 527
파단시 신율 6 / 4 % ISO 527
챠피 충격 강도, +23°C 40 / 28 kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 30 / 24 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 6 / 3 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 5 / 2 kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 261 / * °C ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa 105 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 190 / * °C ISO 75-1/-2
1.5mm 평균두께에서의 난연성 HB / * class IEC 60695-11-10
테스트 두께 1.6 / * mm -
두께 H인 제품의 난연성 HB / * class IEC 60695-11-10
테스트 두께 0.8 / * mm -
전기적 특성건조/응축단위시험규격
ISO 데이터
상대 유전뮬, 1MHz 5.1 / 3.6 - IEC 62631-2-1
소산 인자, 1MHz 2000 / 250 E-4 IEC 62631-2-1
부피 저항 1E10 / 1E13 Ohm*m IEC 62631-3-1
표면 저항 * / 1E10 Ohm IEC 62631-3-2
전기 압력 40 / 60 kV/mm IEC 60243-1
CTI 500 / - - IEC 60112
기타 특성건조/응축단위시험규격
물에서의 흡수성 6 / * % ISO 62와 유사
조건에서의 흡습성 2 / * % ISO 62와 유사
밀도 - / 1340 kg/m³ ISO 1183
물질의 비성질건조/응축단위시험규격
ISO 데이터
점도수 150 / * cm³/g ISO 307, 1157, 1628
테스트 견본 생산값단위시험규격
ISO 데이터
사출성형: 용융수지온도 280 °C ISO 294
사출성형: 금형온도 80 °C ISO 294
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이)
지역별 검색
짱쨌쨈
기타 정보
사출 성형
PREPROCESSING
Max. Water Content 0,1%
Pre-Drying: 80°C 4 Hours
PROCESSING
Melt Temperature 280-300°C
Mould Temperature 80-90°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.